In response to the requirements of our customers, the company's maintenance of the LCD splicing screen will be explained as follows:
LCD splicing screens can easily overheat certain pixels due to prolonged work. Once it exceeds the limit, it will cause permanent damage. This forms a “bad point†that we often say. Since the pixels of a liquid crystal splicing screen are composed of liquid crystals, when it is continuously operated at full load for more than 96 hours, it will accelerate its aging, and even burn out in severe cases. So, if we have to work for a long time, it is best to intermittently let it rest for a while, or often to change the screen appearance at different time intervals, because we need to reduce the brightness while waiting for work, or it is in the screen saver The mode of operation for a while, this simple approach can not only delay the aging of the LCD screen, but also to avoid hardware damage.
The LCD display screen is very fragile and delicate, and its impact resistance is not so strong. This is because the LCD contains many precision glass components and agile electrical components that can cause damage to the LCD screen and other related components in the event of a strong impact. So be sure to avoid strong shocks. At the same time, we must pay attention not to exert pressure on the surface of the LCD screen, such as pointing a certain part of the screen with a finger, which can easily cause an increase in the number of dead pixels.
Also, no matter what problems the LCD splicing screen is, it is forbidden to assemble the LCD splicing screen by itself (especially for the general DIY interesters), if the LCD splicing screen is not working properly, it can be found by the manufacturer. Since the transformer in the LCD backlighting assembly may still have a high voltage of 1000 V (albeit a micro-current) after being turned off for a certain period of time, non-professionals may cause new failures of the assembly if not handled properly.
In addition, if you find that the surface of the LCD spliced ​​screen has dirt, you should use an accurate method to remove the dirt. The media used is preferably a soft, non-fibrous material, such as absorbent cotton, lens paper, or a soft cloth, and then wiped off with a little glass cleaner, prohibit the use of chemical solutions such as alcohol, can not use rough Cloth or paper items, because these materials are prone to scratches. Here we must remind everyone that do not spray the cleaning directly to the surface of the screen, it is very easy to flow to the screen inside the LCD screen to cause short-circuit failure, causing unnecessary losses.
LCD splicing screens can easily overheat certain pixels due to prolonged work. Once it exceeds the limit, it will cause permanent damage. This forms a “bad point†that we often say. Since the pixels of a liquid crystal splicing screen are composed of liquid crystals, when it is continuously operated at full load for more than 96 hours, it will accelerate its aging, and even burn out in severe cases. So, if we have to work for a long time, it is best to intermittently let it rest for a while, or often to change the screen appearance at different time intervals, because we need to reduce the brightness while waiting for work, or it is in the screen saver The mode of operation for a while, this simple approach can not only delay the aging of the LCD screen, but also to avoid hardware damage.
The LCD display screen is very fragile and delicate, and its impact resistance is not so strong. This is because the LCD contains many precision glass components and agile electrical components that can cause damage to the LCD screen and other related components in the event of a strong impact. So be sure to avoid strong shocks. At the same time, we must pay attention not to exert pressure on the surface of the LCD screen, such as pointing a certain part of the screen with a finger, which can easily cause an increase in the number of dead pixels.
Also, no matter what problems the LCD splicing screen is, it is forbidden to assemble the LCD splicing screen by itself (especially for the general DIY interesters), if the LCD splicing screen is not working properly, it can be found by the manufacturer. Since the transformer in the LCD backlighting assembly may still have a high voltage of 1000 V (albeit a micro-current) after being turned off for a certain period of time, non-professionals may cause new failures of the assembly if not handled properly.
In addition, if you find that the surface of the LCD spliced ​​screen has dirt, you should use an accurate method to remove the dirt. The media used is preferably a soft, non-fibrous material, such as absorbent cotton, lens paper, or a soft cloth, and then wiped off with a little glass cleaner, prohibit the use of chemical solutions such as alcohol, can not use rough Cloth or paper items, because these materials are prone to scratches. Here we must remind everyone that do not spray the cleaning directly to the surface of the screen, it is very easy to flow to the screen inside the LCD screen to cause short-circuit failure, causing unnecessary losses.
Retractable Ceiling Fan,rechargeable fan with solar panel,solar and rechargeable fan
JIANGMEN ESCLIGHTING TECHNOLOGY LIMITED , https://www.jmesclightingfan.com