In the new material park, due to the frequent entry and exit of vehicles, the damage to the ground is relatively large, and professional wear-resistant floor treatment is required. It is recommended to choose the emery wear floor. Emery wear-resistant floor is also called inorganic aggregate wear-resistant floor, wear-resistant ground. Wear-resistant floor, hardened floor, hardened floor, hard floor, hard floor. The wear-resistant flooring material is a ready-mixed, on-site, dry-sand ground hardener in the factory. Mainly consists of high-strength cement, inorganic wear-resistant aggregate, pigment powder (cement color no), additives and other components. Advantages: The color is optional, the surface is dense, easy to dust, and easy to clean; it is a substitute for the traditional industrial surface terrazzo; synchronous construction with concrete can be quickly put into use; low cost, high cost performance, long service life; wear resistance, resistance Excellent impact and compression properties.
How to distinguish the advantages and disadvantages of emery?
Advantages: The color is optional, the surface is dense, easy to dust, and easy to clean; it is a substitute for the traditional industrial surface terrazzo; synchronous construction with concrete can be quickly put into use; low cost, silicon carbide price, high cost performance, long service life; wear-resistant Excellent performance, impact resistance, and pressure resistance.
Scope of application: The wear-resistant floor is suitable for floors that need to withstand frequent movements of vehicles, often with heavy impact, often with sharp hardening friction, non-corrosive chemicals, low cleanliness requirements, and low aesthetic requirements. .
The concrete strength of the grass-roots level shall be higher than C25, the water-cement ratio shall be controlled below 0.50, and the concrete fall-out difference shall be controlled within 70-100mm. The concrete mixture shall minimize the segregation and control the bleeding. In order to ensure that the concrete mixture has sufficient fluidity and conducive to construction, it is recommended that concrete be added with proper additives.
Base concrete should be poured and tamped with reference to the standard of fine concrete. Attention should be paid to accurate dimensions and to reduce laitance production. The hardener surface is preferably constructed at the same time as the concrete structure layer. For example, the leveling layer concrete should be fine-grained concrete with a thickness of not less than 50mm, and a telescopic reinforcement mesh should be considered. Particular attention should be paid to the corners of the concrete construction block of the grass-roots level to ensure that the concrete at the site is vibrated and compacted, and additional strengthening treatment should be taken.
First of all, the silicon carbide sand bricks should be accurate in size. The proportion of corundum is generally between 2.45 and 2.6. Sandblasting corundum, the proportion is too small or too large indicates that the material itself is not pure, and other refractory materials must be added, which greatly affects the corundum. The content affects the heat transfer performance of corundum. In the purchase of emery, to see whether the surface of the brick corners and cracks, Shandong corundum, missing corners and cracks should be acceptable within the scope of the national standard, if seriously exceeded the national standard standards, the batch of product quality is not qualified. Our company reminds you to supervise the loading of carton boxes on the spot when purchasing carborundum to avoid product damage and destruction caused by barbaric construction.
Attention points in use: The color selection has certain limitations, the common colors are only cement primary colors, gray, green, red, etc.; some low-quality color (such as green) wear-resistant floor will fade in a short time; Even if it is a color-resistant floor, its color cannot be as pure and saturated as an epoxy floor; its permeability is poor. The wear-resisting floor is actually a kind of high-strength concrete. Its anti-permeability performance is far less than that of an epoxy floor. For some workshops where oil is often present, such as a machine shop, oil can easily seep into the floor and cause incompleteness. Clean; poor corrosion resistance, inorganic silicate-based chemical composition, easily acidic and alkaline corrosion; surface finish is far less than the epoxy floor, especially the poor quality of the wearable floor may also get ash, Therefore, it does not apply to floors that require a high degree of cleanliness. Scope of application: The wear-resistant floor is suitable for floors that need to withstand frequent movements of vehicles, often with heavy impact, often with sharp hardening friction, non-corrosive chemicals, low cleanliness requirements, and low aesthetic requirements. .
How to distinguish the advantages and disadvantages of emery?
Advantages: The color is optional, the surface is dense, easy to dust, and easy to clean; it is a substitute for the traditional industrial surface terrazzo; synchronous construction with concrete can be quickly put into use; low cost, silicon carbide price, high cost performance, long service life; wear-resistant Excellent performance, impact resistance, and pressure resistance.
Scope of application: The wear-resistant floor is suitable for floors that need to withstand frequent movements of vehicles, often with heavy impact, often with sharp hardening friction, non-corrosive chemicals, low cleanliness requirements, and low aesthetic requirements. .
The concrete strength of the grass-roots level shall be higher than C25, the water-cement ratio shall be controlled below 0.50, and the concrete fall-out difference shall be controlled within 70-100mm. The concrete mixture shall minimize the segregation and control the bleeding. In order to ensure that the concrete mixture has sufficient fluidity and conducive to construction, it is recommended that concrete be added with proper additives.
Base concrete should be poured and tamped with reference to the standard of fine concrete. Attention should be paid to accurate dimensions and to reduce laitance production. The hardener surface is preferably constructed at the same time as the concrete structure layer. For example, the leveling layer concrete should be fine-grained concrete with a thickness of not less than 50mm, and a telescopic reinforcement mesh should be considered. Particular attention should be paid to the corners of the concrete construction block of the grass-roots level to ensure that the concrete at the site is vibrated and compacted, and additional strengthening treatment should be taken.
First of all, the silicon carbide sand bricks should be accurate in size. The proportion of corundum is generally between 2.45 and 2.6. Sandblasting corundum, the proportion is too small or too large indicates that the material itself is not pure, and other refractory materials must be added, which greatly affects the corundum. The content affects the heat transfer performance of corundum. In the purchase of emery, to see whether the surface of the brick corners and cracks, Shandong corundum, missing corners and cracks should be acceptable within the scope of the national standard, if seriously exceeded the national standard standards, the batch of product quality is not qualified. Our company reminds you to supervise the loading of carton boxes on the spot when purchasing carborundum to avoid product damage and destruction caused by barbaric construction.
Attention points in use: The color selection has certain limitations, the common colors are only cement primary colors, gray, green, red, etc.; some low-quality color (such as green) wear-resistant floor will fade in a short time; Even if it is a color-resistant floor, its color cannot be as pure and saturated as an epoxy floor; its permeability is poor. The wear-resisting floor is actually a kind of high-strength concrete. Its anti-permeability performance is far less than that of an epoxy floor. For some workshops where oil is often present, such as a machine shop, oil can easily seep into the floor and cause incompleteness. Clean; poor corrosion resistance, inorganic silicate-based chemical composition, easily acidic and alkaline corrosion; surface finish is far less than the epoxy floor, especially the poor quality of the wearable floor may also get ash, Therefore, it does not apply to floors that require a high degree of cleanliness. Scope of application: The wear-resistant floor is suitable for floors that need to withstand frequent movements of vehicles, often with heavy impact, often with sharp hardening friction, non-corrosive chemicals, low cleanliness requirements, and low aesthetic requirements. .
CHANGZHOU CLD AUTO ELECTRICAL CO.,LTD , https://www.cld-led.com