Parking system is more and more widely used in large and small parking lots across the country. The application of parking system brings convenience to people. At the same time, some problems often arise in daily management. How can we exclude parking lots? What are the common faults in the system? The following is a summary of how to eliminate the common faults in the parking system.
Common Fault One: Parking Software Failure
1. The software crashes when it enters and exits management (1) Restarts the computer (2) Conflicts between video cards and other cards, Change slots (3) Change the interrupt number, 2 The software cannot enter the access management (1) Check whether the card reader is Turn on the communication is normal (2) The network is normal (3) The computer graphics card is set normally (4) The system setting is normal 3. The software responds slowly when the card is swiped or the computer hangs up (1) Check whether the operating system is normal (reinstall the system)
(2) The vehicle library data can not be too much (filing a small amount of data)
(3) Whether the network is stable and the transmission rate is low (adjustment speed)
(4) Whether the workstation settings are normal (unified setting)
4, the software image does not take pictures or can not retain the image (1) check the mapped network drive is normal (reset)
(2) Whether the image is deleted (3) Check if the image is saved 0 days 5, the image is not clear (1) The video is not set properly (normal setting)
(2) monitor resolution, color desktop size adjustment
6, the computer is unstable, the system often goes wrong, easy to operate when the software crashes (1) the computer kills the virus (2) check the computer records the vehicle record is too much 7, the computer network is unstable, disconnected when the time (1) RJ -4S head bad, replaceable (2) BNC head terminal resistance bad, (replacement)
(3) HUB power supply is stable (4) card settings are changes <br> <br> Troubleshooting II: Gone with the Wind box all communication barrier
1, check whether the ticket box is turned on (power is turned on)
2. Check if the serial port is set incorrectly (make sure to use the serial port)
3, check the communication bus for short circuit or open circuit (excluding communication lines and circuit breakers)
4, inspection RS485 card communication 5, the computer motherboard serial port is bad (maintenance computer motherboard or replace the motherboard)
Common fault 3: The ticket box fails to communicate
1, check the ticket box number is set correctly (machine number reset correctly)
2. Check the control board communication chip communication 3. Check the read/write module reading/writing status of the read/write board 4. Check the external environment interference of the read/write board (reliable grounding, eliminate interference factors)
Common fault four: card reader card failure
1. No response to reading card (check read-write antenna, read-write module, SCM, whether there is a car reading card for machine settings)
2. There is no opening of the card reader (check whether the opening line is connected)
3ã€Is the IC card expired or reported (delayed or untied)?
No. 3, No. 3 machine temporary reader opening device number set wrong 5, whether the software is confirmed to open the gate (software settings or SCM settings)
Common fault five: card reader other faults
1. The card reader is often automatically turned off (1) Is the power supply 220V normal (normal power supply is about 220V)
(2) SCM bad contact (re-inserted chip)
(3) Caused by interference (reliable grounding or corresponding anti-interference measures)
2, ID card can not enter the field (1) Communication failure (excluding communication failures)
(2) software failure (reboot the computer)
(3) ID card battery is low (replace battery)
Common fault six: card machine failure
1. The card out board is equipped with a car or no car out card jumper (set the corresponding jumper)
2, check out the card board 3, check the card machine button (replace the Fuji button)
4, check the card machine transformer power supply (replacement transformer)
5. Check the mechanical part of the card machine (replace the mechanical part of the card machine)
6, check the sense of the signal (sense reset)
7, IC card deformation (deformed IC card is not placed on the card machine)
Common fault seven: display garbled
1, check whether the display water (blow water treatment)
2, too much dust short circuit (dust removal processing)
3, SCM loose (re-inserted until the microcontroller is normal)
Common fault eight: the display does not show
1, the display no power (replacement transformer or Phoenix plug-in line connected)
2, check the display board MCU (replace MCU)
3, check the display board (replace the display board)
Common failure nine: no voice card reader
1, check the speaker or the line (replace the horn or re-welding)
2, check the voice chip (power reset or replace the voice chip)
3, voice potentiometer adjustment is not adjusted (adjust potentiometer)
Frequently Asked Questions Ten: Intercom System Cannot Be Used
1. There is no sound for the intercom extension (replace the speaker or check the line)
2, the host can not talk (bad host speakers or button contact)
3, the host noise (interference caused by the speaker cable shield grounding)
The above is a common failure of the parking system in daily use. I hope to help everyone. Of course, if you can not eliminate and deal with the problem, it is best to communicate with the manufacturer in a timely manner.
Common Fault One: Parking Software Failure
1. The software crashes when it enters and exits management (1) Restarts the computer (2) Conflicts between video cards and other cards, Change slots (3) Change the interrupt number, 2 The software cannot enter the access management (1) Check whether the card reader is Turn on the communication is normal (2) The network is normal (3) The computer graphics card is set normally (4) The system setting is normal 3. The software responds slowly when the card is swiped or the computer hangs up (1) Check whether the operating system is normal (reinstall the system)
(2) The vehicle library data can not be too much (filing a small amount of data)
(3) Whether the network is stable and the transmission rate is low (adjustment speed)
(4) Whether the workstation settings are normal (unified setting)
4, the software image does not take pictures or can not retain the image (1) check the mapped network drive is normal (reset)
(2) Whether the image is deleted (3) Check if the image is saved 0 days 5, the image is not clear (1) The video is not set properly (normal setting)
(2) monitor resolution, color desktop size adjustment
6, the computer is unstable, the system often goes wrong, easy to operate when the software crashes (1) the computer kills the virus (2) check the computer records the vehicle record is too much 7, the computer network is unstable, disconnected when the time (1) RJ -4S head bad, replaceable (2) BNC head terminal resistance bad, (replacement)
(3) HUB power supply is stable (4) card settings are changes <br> <br> Troubleshooting II: Gone with the Wind box all communication barrier
1, check whether the ticket box is turned on (power is turned on)
2. Check if the serial port is set incorrectly (make sure to use the serial port)
3, check the communication bus for short circuit or open circuit (excluding communication lines and circuit breakers)
4, inspection RS485 card communication 5, the computer motherboard serial port is bad (maintenance computer motherboard or replace the motherboard)
Common fault 3: The ticket box fails to communicate
1, check the ticket box number is set correctly (machine number reset correctly)
2. Check the control board communication chip communication 3. Check the read/write module reading/writing status of the read/write board 4. Check the external environment interference of the read/write board (reliable grounding, eliminate interference factors)
Common fault four: card reader card failure
1. No response to reading card (check read-write antenna, read-write module, SCM, whether there is a car reading card for machine settings)
2. There is no opening of the card reader (check whether the opening line is connected)
3ã€Is the IC card expired or reported (delayed or untied)?
No. 3, No. 3 machine temporary reader opening device number set wrong 5, whether the software is confirmed to open the gate (software settings or SCM settings)
Common fault five: card reader other faults
1. The card reader is often automatically turned off (1) Is the power supply 220V normal (normal power supply is about 220V)
(2) SCM bad contact (re-inserted chip)
(3) Caused by interference (reliable grounding or corresponding anti-interference measures)
2, ID card can not enter the field (1) Communication failure (excluding communication failures)
(2) software failure (reboot the computer)
(3) ID card battery is low (replace battery)
Common fault six: card machine failure
1. The card out board is equipped with a car or no car out card jumper (set the corresponding jumper)
2, check out the card board 3, check the card machine button (replace the Fuji button)
4, check the card machine transformer power supply (replacement transformer)
5. Check the mechanical part of the card machine (replace the mechanical part of the card machine)
6, check the sense of the signal (sense reset)
7, IC card deformation (deformed IC card is not placed on the card machine)
Common fault seven: display garbled
1, check whether the display water (blow water treatment)
2, too much dust short circuit (dust removal processing)
3, SCM loose (re-inserted until the microcontroller is normal)
Common fault eight: the display does not show
1, the display no power (replacement transformer or Phoenix plug-in line connected)
2, check the display board MCU (replace MCU)
3, check the display board (replace the display board)
Common failure nine: no voice card reader
1, check the speaker or the line (replace the horn or re-welding)
2, check the voice chip (power reset or replace the voice chip)
3, voice potentiometer adjustment is not adjusted (adjust potentiometer)
Frequently Asked Questions Ten: Intercom System Cannot Be Used
1. There is no sound for the intercom extension (replace the speaker or check the line)
2, the host can not talk (bad host speakers or button contact)
3, the host noise (interference caused by the speaker cable shield grounding)
The above is a common failure of the parking system in daily use. I hope to help everyone. Of course, if you can not eliminate and deal with the problem, it is best to communicate with the manufacturer in a timely manner.
Hex Screws,Screws And Bolts,Screw And Nut,Fastener Bolt
NINGBO YWC IMP. & EXP. CO.,LTD , https://www.nbywc-fastener.com