| Home>Bearing knowledge>The reason for affecting SKF imported bearings grinding 蜕 层 |
Factors affecting the grinding of the 蜕 层 layer of SKF imported bearings
Source: China Bearing Network Time: 2013-04-19
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
1. Grinding heat in the grinding process; grinding wheel and workpiece touch area; cost a lot of energy; many grinding heat occurs; part of the instantaneous high temperature that constitutes the grinding zone. Use the linear motion heat source heat transfer theory formula to derive, account or The infrared temperature method and the thermocouple method are used to measure the instantaneous temperature under the test conditions; the instantaneous temperature in the grinding zone can be as high as 1000 to 1500 ° C in the range of 0.1 to 0. 001 ms. Such instantaneous high temperature; SKF is sufficient for the operation appearance High-temperature oxidation of the outer surface of the inevitable depth; amorphous arrangement, high temperature tempering, secondary quenching; and even burn cracking and other changes.
.1) The effect of the outer surface of the oxide layer on the appearance of oxygen in the steel and the oxygen in the air; the thin layer of iron oxide which is raised to the pole of 20 to 30 nm. It is worth noting that the thickness of the oxide layer and the total thickness of the enthalpy layer of the external grinding The test results are in a corresponding relationship. This indicates that the thickness of the oxide layer is directly related to the grinding process; it is an important mark of the grinding quality.
.2) Amorphous arrangement The instantaneous high temperature of the grinding zone causes the workpiece SKF inlet bearing to reach the molten state; the molten metal molecular flow is uniformly applied to the work surface; and is cooled by the base metal at a very fast speed. It constitutes a very thin layer of amorphous arrangement. It has high hardness and resistance; but it only needs about 10nm; it is very simple to be removed in the fine grinding process.
.3) The instantaneous high temperature in the grinding zone of the high temperature tempering layer can be heated to a temperature higher than the tempering heating of the workpiece at a certain depth (10 to 100 nm). In the case where the austenitizing temperature is not reached; The improvement of the heating temperature; the appearance of layer-by-layer will occur with the re-tempering or high-temperature tempering corresponding to the heating temperature; the hardness will also decrease. The higher the heating temperature, the more the hardness is reduced. SKF Bearing. 4) The second layer of quenching layer heats the outer surface of the workpiece to austenitizing temperature (Ac1) when the instantaneous high temperature of the grinding zone is above; then the austenitizing of the layer is arranged in the subsequent cooling process; Stellite arrangement. However, any workpiece with secondary quenching burns must be a high temperature tempering layer with extremely low hardness under the secondary quenching layer.
.5) Grinding cracks Secondary quenching burns will change the stress of the outer surface of the workpiece. The secondary quenching zone is under pressure; the maximum tensile stress exists in the high temperature tempering zone below; here is the most likely crack center The local crack is most simply conveyed along the original austenite grain boundary. Severe burns will cause cracks in the entire surface of the grinding surface.
2. Molting layer SKF
During the grinding process; the outer surface of the workpiece will be affected by the cutting force, tightening force and friction of the grinding wheel. Especially the effect of the latter two; the outer surface of the workpiece constitutes a highly directional plastic deformation layer and work hardening layer These metamorphic layers must affect the change of residual stress in the outer layer.
.1) The cold plastic deformation layer is in the grinding process; each moment the abrasive grain is equivalent to a cutting edge. However, in many cases, the rake angle of the cutting edge is negative; the abrasive grain is in addition to the cutting effect; The appearance of the kneading effect (ploughing effect); leaving a significant plastic deformation layer on the surface of the workpiece. The degree of deformation of this deformation layer will increase with the degree of grinding wheel blunt and the increase of grinding feed.
.2) Thermoplastic deformation (or high temperature deformation) The instantaneous temperature at which the layer grinding heat is formed on the outside of the work; the SKF bearing causes the elastic limit of the outer surface of the workpiece to be drastically reduced at a certain depth; and even reaches the degree of elasticity. At this moment, the outer surface of the work is ground. Cutting force; especially under the effect of tightening force and friction; causing the free expansion; being bound by the base metal; the outer surface being tightened (more plowed); the outer surface layer is plastically deformed. The high temperature plastic deformation is unchanged in the grinding process In the case; as the external temperature of the workpiece increases.
.3) The work hardening layer can sometimes be found by microhardness method and metallographic method; the hardness of the outer layer is increased due to processing deformation.
In addition to the grinding process; the outer decarburization layer formed by casting and heat treatment heating; if it is not completely gone in the future processing; the residual surface will also constitute the surface softening and transformation; promote the early failure of SKF imported bearings.
Recommend to friends comments close window
| Bearing related knowledge |
| Analysis of the comparison test in the national watch: wheel bearing seal layout bearing information The reason for the oscillation of FAG bearing is how to smooth the slewing bearing NSK bearing cooperation effect and selection tips |
This article links to http://
Please indicate the bearing network http://
Previous:Analysis: How to cooperate with bearings and shafts Next: The precautions when using KOYO bearings
Cut-Off Wheels is a simplified product of thousands of impeller, mainly used in industrial production of polishing, is also a kind of industrial consumables products. The impeller matrix has mesh cloth, nylon, plastic, steel paper, etc., the number of pages varies, and is evenly distributed in fan shape. Particle size 36#-400#, 60#, 80# is the most common, the outer diameter of 4"-7" installed in the angular grinder, used for welding seam, positive edge burr grinding and grinding processing, can be interchangeable with the cymbal grinding wheel, has the advantages of good elasticity, high efficiency, good heat loss, low noise can replace the resin cymbal grinding wheel, it has strong elasticity, high tensile and bending strength, Good self-sharpening, high grinding rate, low noise, suitable for grinding the welding seam in the box and the flash edge of the stamping parts. It is mainly used for grinding and polishing of various stainless steel and carbon steel structural parts.
Cut-Off Wheels,Grinding Wheel,Disc For Angle Grinde,Flap Wheel
Behappy Crafts (suzhou)Co.,Ltd , https://www.jshaoyue.com