Analysis of NSK skills: equipment for cylindrical bore bearings

Source: Bearing network time: 2018-02-14

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

Cylindrical hole bearing equipment is pressed by the press. Small bearings are widely used by presses. As shown in Figure 1, the block is pressed against the inner ring; the press is slowly pressed to the end of the inner ring. Shaft shoulder. The outer ring is placed against the inner ring of the block device; it will form an indentation or crush on the raceway; so it must be stopped.
In addition; when operating; should be oiled on the cooperation surface in advance. It is a must to hit the equipment with a hoe; it should be padded on the inner ring. This practice repeatedly forms bearing damage; therefore; only limited to small interference The condition; can not be used for large interference or medium and large bearings.
Non-displacement bearings such as deep groove ball bearings; occasions where the inner and outer rings require interference equipment; as shown in Figure 2; use screw or oil pressure; use the spacer to press the inner and outer rings together. Self-aligning ball bearings The outer ring is easy to skew; even if it is not an interference cooperation; it is also the best padding equipment.
Separate bearings such as cylindrical roller bearings, tapered roller bearings; can be equipped with the inner and outer rings respectively to the shaft and the bearing seat. When the inner ring and the outer ring of the equipment are combined respectively; the key points are firmly closed; The two are in violation of each other; barely press in will form a roll to the surface.
Hot-packing method <br> Large-sized bearing; requires a lot of force when pressing; so it is difficult to work. Therefore; widely used hot-packing method: heating the bearing in oil; making it swell; then loading it on the shaft. This method; the equipment will not present a situation of improper force; can shorten the working time.
The heating temperature of the bearing; the bearing scale, the required interference; refer to Figure 3. Resolution. Precautions for hot loading operations;
(a) Bearing heating does not exceed 120 ã‚šC.
(b) In order to prevent the bearing from touching the bottom of the oil sump; the bearing should be placed on a metal grid; or hoisted.
(c) In order to avoid operation; it is difficult to equipment due to the lower inner ring temperature; the bearing should be heated 20 Â° C higher than the required temperature by 30 Â° C.
(d) After the equipment; the bearing is cooled; the width direction is also shortened; so use a shaft nut or other suitable method; lock it; to prevent a gap between the inner ring and the bearing shoulder.
NSK induction heating equipment <br> In addition to oil heating, NSK induction heating equipment using electromagnetic induction principle is also widely used.
NSK induction heating equipment; built-in excitation coil; due to electromagnetic induction after power-on; current is transmitted to the heating body (bearing); heat is generated by the impedance of the bearing itself. Therefore, it can be in a short time; no heat is required to uniformly heat the bearing. High efficiency of loading work; health.
For occasions where loading and unloading are frequent; for example, roller bearings, cylindrical roller bearings for axleboxes for railway vehicles; NSK's special induction heating equipment can be used for equipment and disassembly of the inner ring.

Recommend to friends comments close window

Bearing related knowledge

Several commonly used bearing types (1)
China rolling mill oil film bearing skills (2)
A simple analysis of single ball bearings and oil-impregnated bearings The fundamental type of rolling bearings can be used to distinguish whether SKF bearings can be reused.

This article links to http://
Please indicate China Bearing Network http://

Previous:High-speed bearing device, cooperation and adjustment method Next: Combination needle roller bearing layout and information

Peristaltic Pump Tubing

For the Peristaltic Pump Tubing, We have different material choices for your various liquids. The standard tube is silicon tubing which conforms to the FDA certificate. Except that we also offer the Saint-Gobain imported tubing, Eg.: NorpreneÂ®A-60-F/NorpreneÂ®chemical /PharmedÂ® BPT... Which suitable for various chemical-based liquid.

Suitable for various industrial applications.

Norprene Chemical Tube,Peristaltic Pump Transfer Tube,Peristaltic Pump Hose,Peristaltic Pump Tube

Baoding Chuangrui Precision Pump Co., Ltd. , https://www.chuangruipump.com