The angle valve is one of the hardware accessories. Almost every house decoration needs to use 5 to 7 angle valves. It is usually used in the bathroom, kitchen and wash basin. Many people may not know the angle valve very well, so today we will Let's see what the angle valve is and how to install the angle valve correctly!
What is an angle valve? 1. Normally, the inlet pipe connection of a faucet is an internal wire nut, and the water outlet on the wall is an internal wire joint, so an angle valve is needed for conversion connection. In this way, it is good to turn off the angle valve directly when installing and debugging the faucet and when repairing the faucet, and it will not affect the use of his area.
What is an angle valve? 2. The angle valve is also equivalent to the safety of the faucet. After the faucet has problems, close the angle valve in time to prevent more serious losses, and it can also limit the water pressure, control the flow of water, and protect. The hose of the faucet!
How to install the angle valve correctly:
1. When connecting the angle valve to the faucet, first clean up the foreign matter in the connecting part and keep both clean.
2. When tightening the inner thread in the wall of the angle valve, pay attention to its winding direction. Generally, it rotates clockwise to the right, but when winding the remaining material on the angle valve, you must go to his back. The direction is counterclockwise to the left, so that when the angle valve is screwed, it will be tightened more and more tightly, and it is not easy to loosen.
3. When wrapping, be sure to tighten its raw material tape, so that the raw material tape can be closely attached to the thread, the tighter the better, if it is loose, it is not easy to handle, remember after the winding Compress by hand in a circle, of course you can also compress while wrapping.
4. There is no rigid requirement for winding a few times, as long as it can be screwed tightly and does not leak, but according to past experience, generally it needs to be wound more than a dozen times to ensure its sealing effect.
5. When screwing the thread, don't screw it into the dead, you can keep a little bit of strength, you don't have to screw it until it can't be screwed, and you don't leak. When you screw it, you only need to feel the feel can be hard. Be sure to pay attention to the depth of screwing in. For example, if the two bent feet of the cold and hot water mixing valve are wire-to-wire, then you must pay attention to keeping them at the same distance from the wall when screwing, especially at their depth Are not consistent.
Editor's summary: The above is what the editor shared about the angle valve and how to install the angle valve correctly. Not every outlet of the angle valve must be upwards. This is determined according to the actual situation. If the hose is shorter, the angle valve will point in the direction of the natural bending of the hose; if the hose is longer, you can let The outlet of the angle valve is inclined downward.
What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount
If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.
Roller shutter door , also known as "shutter door", lots of panel pieces connected together, fixed in the guide rail , take above reel as the center of rotation.
Roller shutter door is used for commercial facades, garages, shopping malls, hospitals, factories and mines and other public places or residential.Electric roller shutter door, especially for large openings, inconvenient to install the ground door , quick opening effect. Such as for the garage door, shopping mall fire shutter door.
Opening methods: Handing driving mode
Rope driving mode
Remote control driving mode
Electric switch driving mode
Roller Shutter Door,Galvanized Roller Shutter Door,Aluminum Roller Shutter Door,Transparent Roller Shutter Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.selfrepairinghighspeeddoor.com