When the surveillance camera is installed and used, it often encounters some faults. There are no images, unclear images, focal lengths, etc. Some of these problems are caused by the camera itself, and some are caused by improper installation and use. This article focuses on the analysis of the surveillance camera. There are black map solutions for your reference.
Step/method 1. Camera condition: Analysis of bad transformer causes: excessive instability of power supply. Solution: Replace transformer 2. Camera condition: Cause of bad line: Too many connectors or poor line contact Solution: Replace line 3. Camera status: Analysis of the causes of several vertical stripes with equal spacing: Since the characteristic impedance of the video transmission line is not 75Ω, it results in impedance mismatch. Or by the video cable's characteristic impedance and distribution parameters do not meet the requirements caused by the synthesis.
Solution: Generally rely on the "series resistor connected at the beginning" or "terminal and resistor connected" method to solve.
4. Camera status: Caused by the appearance of grainy interference: The quality of the video transmission line is not good, especially the shielding performance is poor, and the line resistance is too large, resulting in a large attenuation of the signal. Or because the power supply system is not "clean".
Solution: Change the video cable or increase the sleeve. The problem of power supply can basically be solved by using a clean power supply or an on-line UPS for the entire system.
5. Camera status: A black bar or white bar appears on the monitor's screen. Cause analysis: The most common fault phenomenon is 50-cycle power frequency interference. This phenomenon is mostly caused by the system generating a ground loop and introducing 50 weeks of work. The presence of ground loops due to frequency interference (AC interference) may be due to the repeated grounding of the common end of the signal transmission line at both ends; or the short circuit of the common end of the signal line to the neutral of the 220V supply; or There is a short circuit between the common terminal of a certain device and the 220V AC power supply; it is also possible that the signal line is caused by a strong magnetic field generated by the AC power supply (such as if both parties are too close together).
Solution: The solution is to connect the transformer in the form of a vertical choke (also known as a neutral transformer), or to use a "longitudinal choke" on the transmission line to eliminate this type of interference. Camera status: Cause analysis of long line: The line is too long or the signal attenuation solution: Due to the loss of the high-frequency end of the image signal is too large, resulting in the basic loss of signals above 3MHz. In this case, either the transmission distance is too long and there is no amplification compensation device in the middle; or the distribution capacitance of the video transmission cable is too large; or the equivalent capacitance is concentrated in the transmission link between the core wire and the shielded wire. As a result, signal amplifiers should be added.
This article comes from China Security Network: http://news. C-ps. Net/2012/4/99231. Html
Stamped cup needle roller bearings are needle roller bearings with a thin stamped and formed outer ring. Its main feature is the low cross-sectional height and high load capacity. It is mainly used for bearing arrangements that are compact, inexpensive and the bore of the bearing housing cannot be used as a raceway for needle cage assembly. Bearings and housings must be installed in an interference fit. If the axial positioning functions such as shoulder and stop ring can be omitted, then the inner hole of the bearing box can be made very simple and economical. Drawn cup needle roller bearings mounted at the end of the shaft are available in double-sided open and single-sided closed versions. The base face of the closed stamped outer ring can withstand small axial guiding forces. Drawn outer ring needle roller bearings generally do not have an inner ring. In cases where the journal cannot be hardened and ground, the inner ring listed in the table can be used. The hardened steel outer ring of a stamped cup needle roller bearing is inseparable from the needle roller cage assembly. The free space to store the lubricant allows for longer relubrication intervals. Bearings are generally designed in a single row. With the exception of the wider bearing series 1522, 1622, 2030, 2538 and 3038, which are fitted with two needle roller cage assemblies. The outer ring of the bearing has lubricating oil holes. Depending on the user's requirements, all single-row drawn cup needle roller bearings with a shaft diameter greater than or equal to 7 mm can be equipped with an outer ring with lubricating holes (code suffix AS1). Needle roller bearings with oil-sealed coils are available with open or closed ends (3 to 5) where the oil seal cannot be fitted due to space constraints. These bearings are equipped with friction seals made of polyurethane or synthetic rubber, filled with lithium-based grease with good rust resistance, and are suitable for operating temperatures from -20 to +100°C. The inner ring of the bearing with oil seal is 1mm wider than the outer ring, which makes the bearing ensure that the oil seal works well and avoid bearing contamination when there is a slight displacement of the shaft relative to the bearing box. The inner ring of the bearing also has lubrication holes, which can be supplemented by the outer ring or the inner ring according to the needs of the bearing arrangement
Needle Bearings,Needle Thrust Bearing,Stainless Steel Needle Bearings,Stainless Steel Needle Roller Bearings
Hebei Fangqiang bearing manufacturing Co., LTD , https://www.fangqiangbearing.com